Drywall sheet weights by brand: lightweight vs regular 1/2 inch
Going by their own documents, the plain 1/2 inch drywall USG, CertainTeed and Georgia-Pacific sell now is the lightweight kind, and a 4x8 sheet of lightweight weighs about 38 to 46 pounds. A 4x12 runs 58 to 70. The brand decides where. USG prints 1.25 lb per square foot for its UltraLight, and Georgia-Pacific prints 1.45 for ToughRock Lite-Weight. Standard fire-rated 5/8 inch Type X is heavier, 2.2 lb a square foot at USG, National Gypsum and Georgia-Pacific, which comes to about 70 lb for a 4x8 and 106 for a 4x12. Their lighter fire-rated 5/8 inch boards run 1.7 to 2.0.
National Gypsum’s older, non-lightweight 1/2 inch board was 1.6 lb a square foot in a 2015 submittal: 51 lb for a 4x8, 77 for a 4x12.
Can one person carry a sheet?
NIOSH, the federal job safety research agency, built its lifting equation around a starting weight of 23 kg, about 51 lb. Canada’s CCOHS explains that this is the load NIOSH considers safe for 75% of women and 90% of men under ideal conditions. Every less-than-ideal factor (reaching far, twisting, lifting high) cuts it down from there. A lightweight 4x8 at 38 to 46 lb comes in under that number. Every 4x12 in the table below goes over it. The lowest figure is 58 lb, the light end of CertainTeed’s range. And pushing a sheet up against the ceiling joists over your head is about as far from ideal as lifting gets.
NIOSH’s own guide for drywall crews, Preventing Injuries from Installing Drywall (publication 2006-147), says to lift one sheet at a time, use two workers for “larger, thicker, and heavier sheets,” and use a drywall lift or drywall jacks for ceilings. Some of its examples have aged. It says a 3/8 inch 4x8 “could weigh 55 pounds,” where USG’s current regular 3/8 inch board is 1.4 lb a square foot, about 45 lb. Its 70 lb for a 5/8 inch 4x8 still matches the Type X figures.
In our view, one person can hang walls of lightweight 4x8s, a sheet at a time. Ceilings are different. For those, get a helper and rent a drywall lift, whatever the brand, and treat 4x12s and 5/8 inch board as two-person sheets on walls too.
Pounds per square foot, maker by maker
The per-sheet columns are our math: the maker’s figure times 32 square feet for a 4x8 and 48 for a 4x12. We read every source on October 17, 2026.
| Board | Maker’s weight, lb per sq ft | 4x8 sheet | 4x12 sheet | Where the number is |
|---|---|---|---|---|
| USG Sheetrock UltraLight, 1/2 in | 1.25 | 40 lb | 60 lb | USG submittal WB2501, rev. 4-20 |
| CertainTeed Easi-Lite, 1/2 in | 1.2 to 1.4 | 38 to 45 lb | 58 to 67 lb | USG’s competitor comparison tool |
| National Gypsum Gold Bond High Strength LITE, 1/2 in | 1.3 to 1.4 | 42 to 45 lb | 62 to 67 lb | National Gypsum submittal, rev. 05 23 |
| Georgia-Pacific ToughRock Lite-Weight, 1/2 in | 1.45 | 46 lb | 70 lb | GP product page |
| National Gypsum Gold Bond regular, 1/2 in | 1.6 | 51 lb | 77 lb | Gold Bond submittal, rev. 04/15 |
| National Gypsum Gold Bond High Strength Fire-Shield 60, 5/8 in | 1.7 | 54 lb | 82 lb | National Gypsum submittal, 05/21 |
| USG Sheetrock UltraLight Firecode X, 5/8 in | 1.9 | 61 lb | 91 lb | USG submittal WB2598, rev. 11-19 |
| Georgia-Pacific ToughRock Lite-Weight Fire-Rated, 5/8 in | 2.0 | 64 lb | 96 lb | GP product page |
| USG Sheetrock Firecode X, 5/8 in | 2.2 | 70 lb | 106 lb | USG submittal WB2964, rev. 3-20 |
| National Gypsum Gold Bond Fire-Shield, 5/8 in Type X | 2.2 | 70 lb | 106 lb | National Gypsum submittal, rev. 05 23 |
| Georgia-Pacific ToughRock Fireguard X, 5/8 in | 2.2 | 70 lb | 106 lb | GP product page |
Two of the pages we read print no weight. CertainTeed’s own Easi-Lite page gives only “up to 30% lighter than traditional 1/2” (12.7 mm) regular panels,” so its row comes from USG’s comparison tool. American Gypsum’s LightRoc submittal doesn’t either. Home Depot lists a LightRoc 1/2 in x 54 in x 12 ft sheet at 76.14 lb, or 1.41 lb a square foot by our math. That’s a store listing, not a maker spec, so it stays out of the table.
Treat every row as approximate. USG and Georgia-Pacific both call their figures that, “for design and shipping purposes.” GP adds that actual weight “may vary depending on manufacturing location and other factors.” Home Depot’s UltraLight 4x8 listing says 39.2 lb, for instance, against 40 from USG’s nominal number.
Two lightweight boards, 10 pounds apart
GP’s ToughRock Lite-Weight is 16% heavier per square foot than USG’s UltraLight. On a 4x12 that’s 70 lb against 60. GP’s light board sits closer to Gold Bond’s old regular sheet (77) than to USG’s.
The “percent lighter” claims won’t sort this out. CertainTeed says up to 30%. National Gypsum says High Strength LITE is “25% lighter than standard 1/2” gypsum board.” A 2011 Georgia-Pacific brochure on sweets.construction.com said “Up to 25% lighter than traditional ½” wall and ceiling drywall products.” USG’s submittal gives no percentage. None of them say what the “standard” board weighed. By our math, National Gypsum’s own 1.3 to 1.4 against its 1.6 regular figure is 12 to 19% lighter, not 25, though the two documents are eight years apart and the board it compared against may have changed. So skip the percent and compare pounds per square foot.
Where regular 1/2 inch board went
You’ll struggle to find a current weight for plain, non-lightweight 1/2 inch board. USG’s submittal for regular Sheetrock panels (rev. 4-20) covers only 1/4 and 3/8 inch. CertainTeed’s regular gypsum board data sheet (CTG-2335) does too. Georgia-Pacific’s ToughRock product list has a 1/4 and 3/8 inch board and a Lite-Weight 1/2 inch, but no plain 1/2 inch regular. In all three, going by those documents, the plain 1/2 inch board for walls and ceilings is the lightweight one.
The 1.6 figure in the table is from National Gypsum’s Gold Bond gypsum board submittal, rev. 04/15, hosted by constructioninstruction.com. American Gypsum still lists 1/2 inch in its ClassicRoc submittal (October 2020) but prints no weight for it. A tag that just says “1/2 inch drywall” doesn’t tell you which row you’re buying. Check the brand.
Loading a truck or trailer
Our drywall sheet count guide puts a 12 by 12 room with 8 foot walls and a ceiling at 13 sheets of 4x12 when you count by area plus 10%. In USG UltraLight that’s 780 lb. In GP Lite-Weight it’s about 905, and in the old Gold Bond regular it would be about 998, a 218 lb difference for the same 13 sheets.
Your truck’s limit is on a sticker, usually on the driver’s side door pillar. Federal rules (49 CFR 571.110, section S4.3) require it to read “The combined weight of occupants and cargo should never exceed” so many pounds. That number includes you.
Home Depot’s Load ’N Go flatbed rental, an F-250, lists a load weight capacity of 3,000 lb. Divided by sheet weight, that’s about 50 sheets of UltraLight 4x12, 43 of GP Lite-Weight, or 28 of 5/8 inch Type X. The listing doesn’t say whether that 3,000 includes the people in the cab.
Other sites say 57 lb
Dumpsters.com uses 1.8 lb a square foot for standard 1/2 inch board (57 lb for a 4x8) and 1.4 for lightweight. Hunker gives 54.4 lb for a standard 4x8 and 40.8 for lightweight. Dumpsters.com names no source. Hunker lists references, one of them a USG Sheetrock document, but doesn’t say which number came from where. The 1.8 is higher than any regular or lightweight 1/2 inch figure we found from a maker, and the 1.4 lightweight figure sits near the heavy end of the range. For sizing a trailer load, high numbers err on the safe side. For deciding whether you can lift a sheet alone, they don’t help much.
To get your own load, run the room through the drywall calculator and multiply its sheet count by your brand’s 4x8 or 4x12 weight above. When it’s time to paint, the paint calculator is next.