Stair rise and run: the code limits and the comfort rules
Under the International Residential Code, a stair’s rise and run have hard limits: each step’s rise (the riser) can be no taller than 7 3/4 inches, and its run (the tread) no shallower than 10 inches, measured from the front edge of one step to the front edge of the next. Those are the legal limits. Comfort is a separate question, and the carpenters’ rule for it says two risers plus one tread should come to about 25 inches. A stair built right at the code limits lands at 25 1/2, which Michael Maines, writing in Fine Homebuilding, still counts as within range.
Half an inch sounds like nothing. On a 9 foot stair, though, one extra riser costs 10 inches of floor and turns a stair that only one of the three comfort rules in JLC’s stair field guide accepts into one that all three accept. On a low deck the problem runs the other way, and the code’s shortest tread makes the step too small.
What the code allows
We read the section text as printed in Boise’s treads and risers handout #437 and handrails handout #436, and in Placer County, California’s residential stairs handout, on November 6, 2026. Placer’s handout prints section R311 of the 2022 California Residential Code under an “IRC commentary” label, and its riser, tread and nosing numbers match Boise’s.
| Rule | Code limit | Section |
|---|---|---|
| Riser height | 7 3/4 in maximum | R311.7.5.1 |
| Tread depth | 10 in minimum | R311.7.5.2 |
| Nosing (the lip past the riser) | 3/4 to 1 1/4 in; not required when the tread is 11 in or deeper | R311.7.5.3 |
| Tallest vs shortest riser in a flight | 3/8 in at most | R311.7.5.1 |
| Deepest vs shallowest tread in a flight | 3/8 in at most | R311.7.5.2 |
| Headroom | 6 ft 8 in | R311.7.2 |
| Width | 36 in clear above the handrail; 31 1/2 in at a handrail on one side, 27 in with rails on both | R311.7.1 |
| Rise of one flight | 151 in (12 ft 7 in), then a landing | R311.7.3 |
| Handrail | at least one side, 34 to 38 in high, on any flight with four or more risers | R311.7.8, R311.7.8.1 |
Tread depth is measured “horizontally between the vertical planes of the foremost projection of adjacent treads,” in Boise’s words. So it’s the step you walk on, front edge to front edge, and the board you nail down is deeper than that by its nosing. The numbers are also “exclusive of carpets, rugs or runners,” so measure bare treads.
Not every town uses these numbers as printed. Maines notes in his Fine Homebuilding article that Rhode Island amended them to an 8 1/4 inch maximum rise and a 9 inch minimum run. That’s looser. Ask your building department which version you’re building to.
Three comfort rules, and they don’t quite agree
Maines works with two rules. Rise plus run should equal 18 inches. Twice the rise plus the run should equal 25. He counts a stair as comfortable when it lands within an inch of both, and his ideal is a 7 inch rise with an 11 inch run.
The JLC Field Guide: Stairs (Jed Dixon, January 2023) has tighter bands and a third rule, and tells you to “use one of the following rules of thumb”:
- two risers plus one tread: 24 to 25 in
- one riser plus one tread: 17 to 18 in
- riser times tread: 70 to 75
It puts the most comfortable riser at 7 to 7 1/2 inches and the most comfortable tread at 10 to 11.
They’re offered as alternatives, so a stair doesn’t have to satisfy all three. Where they split is still worth seeing. Take the code-limit stair: a 7 3/4 inch riser and a 10 inch tread give 25 1/2, 17 3/4 and 77 1/2. Maines lists the same 17 3/4 and 25 1/2 and is fine with both. Of JLC’s three, only riser plus tread accepts it. Maines’ 7 by 11 hits 25 and 18 exactly, yet scores 77 on the multiplication rule, outside JLC’s band.
So the multiplication rule is the strict one. It’s the only rule that turns down the stair Maines calls ideal. We go by 2R + T: both articles print it, and it’s the comfort line our stair calculator shows.
Five ways to build a 9 foot stair
Take a rise of 108 inches, floor to floor, which is the default in our stair calculator for risers, treads and stringer length. Divide by 7.75 and you get 13.9, so the fewest legal risers is 14. That stair is the first row. The others add a riser or two, deepen the treads, or both. The math is ours: riser height is the rise divided by the riser count, treads are one fewer than risers, total run is treads times tread depth, and the stringer is the diagonal of total rise and total run, the same formula the calculator uses.
| Risers | Riser height | Tread | 2R + T | R + T | R × T | JLC rules that accept it | Total run | Stringer |
|---|---|---|---|---|---|---|---|---|
| 14 | 7.71 in | 10 in | 25.4 | 17.7 | 77.1 | 1 of 3 | 130 in (10 ft 10 in) | 169 in |
| 15 | 7.20 in | 10 in | 24.4 | 17.2 | 72.0 | 3 of 3 | 140 in (11 ft 8 in) | 177 in |
| 15 | 7.20 in | 10.5 in | 24.9 | 17.7 | 75.6 | 2 of 3 | 147 in (12 ft 3 in) | 182 in |
| 15 | 7.20 in | 11 in | 25.4 | 18.2 | 79.2 | 0 of 3 | 154 in (12 ft 10 in) | 188 in |
| 16 | 6.75 in | 11 in | 24.5 | 17.8 | 74.3 | 3 of 3 | 165 in (13 ft 9 in) | 197 in |
All five are legal, and all five land within an inch on both of Maines’ tests.
We’d build the second row. It adds one riser and 10 inches of floor. Its risers sit inside JLC’s 7 to 7 1/2 inch sweet spot, and every rule in both articles accepts it. The lumber barely changes: on the diagonal alone, it’s 177 inches against 169, and both are already longer than a 14 foot board (168 inches).
The fourth row is the reminder that these are rules of thumb, which is what JLC calls them. Deeper treads, a gentler stair, no nosing needed at 11 inches, and none of JLC’s three rules accepts it. It misses the first two bands by 0.4 and 0.2 inch and the multiplication rule by about 4, while Maines passes it on both counts. Don’t tear out a stair for scoring 25.4.
Same goes for the 14 riser stair. It’s legal and Maines’ rules pass it. If the floor space isn’t there, say a basement stair that would hit a wall, build it and don’t lose sleep.
A low deck flips the problem
Now a deck whose surface sits 40 inches above the patio. 40 divided by 7.75 is 5.16, so you need 6 risers of 6 2/3 inches. Five risers would be 8 inches each, over the limit.
With the code’s 10 inch treads, that stair scores 23.3, 16.7 and 66.7. None of JLC’s rules accepts it, and it misses both of Maines’ targets by more than an inch. Maines says rise plus run below 17 or above 19 makes steps that need “strides either too big or too small for most people.” Short risers want deeper treads.
Cut the stringers for an 11 inch tread instead and it scores 24.3, 17.7 and 73.3, inside all three of JLC’s bands and both of Maines’. The run grows from 50 inches to 55.
Mike Guertin’s deck stair article in JLC covers the cutting. He says the nosing rule “conveniently works out” at the code-minimum 10 inch cut: a dry 2x12 or a pair of 5 1/2 inch deck boards leaves a 1 1/4 inch overhang, the most the code allows. The pair of deck boards is 11 inches of wood, so on an 11 inch cut it leaves little or no lip. That’s fine. He notes the nosing rule is for tread cuts under 11 inches.
A few more of his numbers. Cut stringers under 5/4 wood decking or 2-by treads can sit no more than 18 inches apart on center, and many synthetic deckings want 12 or 10, some as close as 8, so check the maker’s instructions. He measures the total rise from the finished landing to the top of the decking. And six risers means a handrail, since the code wants one on any flight of four or more.
The 3/8 inch rule and the floor you haven’t laid yet
Measure finish to finish. Take any of the 15 riser rows from the table, and say the stringers are laid out to the upper subfloor, with 3/4 inch hardwood going down up there later. The top riser grows from 7.20 to 7.95 inches. That’s 3/4 inch taller than the rest, twice the 3/8 the code allows, and over the 7 3/4 inch maximum on its own.
Flooring at the bottom does the opposite and shortens the first riser. Outside, a concrete landing poured after the stringers are cut has the same effect. If the finish isn’t down yet, work its thickness into the total rise before you lay out a single step.
Put your own rise in
Open the stair calculator and enter your total rise. It starts at the code limits, 7.75 inch risers and 10 inch treads, and its “2 risers + 1 tread” line shows where you land. Aim for 24 to 25. To get the extra riser from the 9 foot example, lower the max riser box: set it to 7.5 and a 108 inch rise comes out at 15 risers of 7.20 inches. On a low deck, raise the tread depth instead. For a deck that isn’t built yet, the deck calculator counts boards, joists and screws and checks joist spans, and our guide to deck footing depth covers the posts.